Skip to main content

Polecam and the Automator

Learn how to use Polecam robotic pedestals with the Cuez Automator

What is a Polecam pedestal?

Polecam robotic pedestals (such as the PanaPod and AutoPod) are motorised camera pedestals that can be controlled remotely over a network. With the Polecam device, the Cuez Automator can recall a saved preset position whenever an Item or Block is triggered, so your camera moves follow your rundown automatically.

Polecam or Panasonic PTZ? Polecam pedestals understand the same commands as Panasonic PTZ cameras, but they need their own device. For a Polecam pedestal, use the Polecam device described in this article, not Panasonic PTZ.

Note: Each pedestal needs to be added as a separate device in the Automator. If you have multiple pedestals, repeat the setup steps below for each one.

Before you start: Make sure the pedestal is powered on, connected to the network, and reachable from the computer running the Automator. We recommend giving the pedestal a static IP address so it doesn't change between sessions.

Adding a Polecam 'device' to the Automator

In the top right corner of the Automator, we see Devices - this can be either red or green depending on the status of the configured devices. Click it and select Add device.

Next, select Polecam from the Device type dropdown list, then give it a name.

Once the device is selected and given a name, you will see the fields needed to configure it so it can be used with the Automator.

Basic device configuration

You can enable or disable the Polecam device with the Device enabled checkbox, and enter the Host name, which is the IP address of the pedestal (for example 192.168.1.60). By default the host name is set to localhost, so the device will show as Offline (red) until you replace it with your pedestal's IP address. Once the correct address is entered, the device should show as Online (green) in the top right corner.
​

Configuring actions

The next step is to configure each Item and Block with the function you want to perform on the Polecam when triggering the Item or Block - more general information on that in this article.

Available functions

Go to preset

Moves the pedestal to a preset position saved on the pedestal. In the Preset field, pick a preset from the list (Preset 1-30).

This is how the presets in the list map to the presets stored on the pedestal:

Preset in the Automator

Preset on the pedestal

Preset 1 to Preset 10

Presets 1 to 10

Preset 11 to Preset 30

Presets 21 to 40

Presets 11 to 20 on the pedestal itself are not positions. Recalling one runs a pedestal function (such as Auto Calibrate, Pancake or Reboot), so the Automator does not offer them and will not recall them.

Tip: Save your positions as presets on the pedestal first, then select those presets in your Item and Block configurations.
​

Note: Go to preset is currently the only function available for Polecam pedestals. Direct movement and the speed of a move are not controlled by the Automator, so set the speed on the pedestal.

How the connection works

  • The Automator checks the pedestal every 5 seconds, and skips the check while commands are getting through. If the pedestal stops answering, the device shows as Offline after about 10 seconds.

  • The Automator sends one command at a time and never asks the pedestal for its position, so the pedestal is left alone while it moves.

  • If the pedestal refuses a connection, the Automator tries the command again, up to three more times. If a recall still fails (or the pedestal answers that it is busy, does not support the command or the value is out of range), a warning is written to the Automator log and the rundown carries on.

Troubleshooting

  • Device shows offline: Check that the Host name is the pedestal's IP address and not the default localhost, and that the Automator computer can reach the pedestal on the network.

  • Preset doesn't move the pedestal: Confirm the preset is saved on the pedestal itself, and that the function points to the right device. Check the Automator log for a warning about the recall.

  • Multiple pedestals: Each pedestal is a separate device. Check that the right device is selected in each function.

💡 The Polecam integration is available from Automator Stable v1.42.0 (22 October 2026) onwards.

Did this answer your question?